Wish List

Ultralight DB-16 double ball standard arm. The DB-16 is the original standard double ball arm that Ultralight is known for. It is 16" from O-ring to O-ring or 17" total length. It's black in color and made out of 6061 T6 aircraft-grade aluminum with Type III anodizing.

Ultralight DB-CB10 double ball crossbar arm. The DB-CB10 is a double ball crossbar arm. It is 10" from O-ring to O-ring or 11" total length. The ball at each end is our BA-TT and each has a 1/4" hole. The flat bar is 4 1/2" long, has six 1/4" threaded holes and the center has one 1/4" hole. It's black in color, made out of 6061 T6 aircraft-grade aluminum with Type III and the hardware is 316 stainless steel.

Ultralight DB-EXT double ball adjustable arm. The DB-EXT is a double ball adjustable arm. It adjusts from 12 1/2" to 19" measured from O-ring to O-ring or 13 1/2" to 20" for total length. The ball at each end is our BA-TT mounted to two flat bars with a long 1/4" slot. Each flat bar has one 1/4" threaded hole and each ball end has one 1/4" hole. There is a large round plastic knob that can be tightened or loosened for easy adjustment. It's black in color, made out of 6061 T6 aircraft-grade aluminum with Type III and the hardware is 316 stainless steel.

Ultralight GP-TRI-MOUNT GoPro mount. The GP-TRI-MOUNT is tripod mount designed to hold a GoPro. It is plastic with 1/4" mounting hole in the bottom. The hardware included is 316 stainless steel. The bolt that holds the GoPro in places is not included

Ultralight LL-BA quick release base for the LL-BS. The LL-BA was designed to slide onto our BA-TP base plate and the ends to some IKelite trays. It was also made so the LL-BS could be attached to it allowing 3/4" Locline to be used. It is 1 1/2" diameter, 1" tall and has a 1/4" threaded mounting hole on top. Comes with a 1/4"-20 x 1/2" thumb screw and 1/4"-20 x 3/4" philip screw. It's black in color and made out of 6061 T6 aircraft-grade aluminum with Type III anodizing and included hardware is 316 stainless steel.

Ultralight LL-BS bolt on base with 3/4" Locline. The LL-BS was designed to bolt to our LL-BA or any other part that a 3/4" locline would be needed. It is 1 1/2" diameter, 1" tall and has a 1/4" threaded mounting hole on top. It can be bolted to most anything using either the 1/4"-20 x 7/8" or 1/4"-20 x 1 1/4" allen bolts and the two flat washers, one split washer and one 1/4" nut that are included. Also included is an attached section of 3/4" Locline. It's black in color and made out of 6061 T6 aircraft-grade aluminum with Type III anodizing and included hardware is 316 stainless steel.

Ultralight LL-YS YS style light and strobe mount with 1/2" Locline. The LL-YS was designed to hold a YS style light or small strobe using a 5/16" hole. The LL-YS comes with a section of 1/2" Locline attached to it. To attach it to a 3/4" section of Locline an adapter like our LL-AD would be needed to go from 1/2" to 3/4". It's black in color and made out of 6061 T6 aircraft-grade aluminum with Type III anodizing.

Ultralight LL-AD Locline adapter from 1/2" to 3/4". The LL-AD is a adapter used to go from 1/2" to 3/4" Locline. It is black plastic, easy to use and can be snapped on or off when needed.

Ultralight SB-04-BCK long ball mount kit for twin buoyancy arms. The SB-04-BCK is the SB-04 ball mount that comes with two plastic washers. It is designed to attach to the AC-CSLSK2 or the AC-CSKXLSK2 clamps so two large buoyancy arms can be mounted side-by-side over a camera. It is black in color, 4" in length, has a ball mount on one end and a 1/8" thick flat end with a 1/4" hole on the other end. The ball adapter is made out of 6061 T6 aircraft-grade aluminum with Type III anodizing. Two 1/2 x 1/4 x 1/8 plastic washers are supplied with the kit.

Ultralight SB-04 long ball mount. The SB-04 was designed as a universal ball mount that can be bolted between a handle and ball or used to attach to something to be used as an additional ball mount. It is also part of the SB-04-BCK kit. It is black in color, 4" in length, has a ball mount on one end and a 1/8" thick flat end with a 1/4" hole on the other end. The ball adapter is made out of 6061 T6 aircraft-grade aluminum with Type III anodizing.

Ultralight SB-11 single ball flat arm. The SB-11 was designed to be an adjustable universal arm with a ball at one end especially because of the 7" long 1/4" slot. The flat arm is part of our adjustable tripod arms with a BA-TT ball mount attached to one end. Total length is 11" and it has one 1/4" threaded hole at the non-ball end. It's black in color and made out of 6061 T6 aircraft-grade aluminum with Type III anodizing.

Ultralight SBSS-5 YS style single ball arm. The SBSS-5 is a YS style single ball standard arm. It was made for Sea & Sea strobes and lights using the YS style mount. It has a 5/16" and 3/8" hole on one end, 1" ball on the other and measures 5" from O-ring to the 5/16" hole with a 6" total length. It's black in color and made out of 6061 T6 aircraft-grade aluminum with Type III anodizing.

Ultralight SBSS-5RB YS style single ball arm with large knob. The SBSS-5RB is like our standard DB-05 arm but with a single ball on one end a 1/2" thick flat surface on the other with two holes. It measures 5" from O-ring to the 5/16" hole with a 6" total length. The two holes are 5/16" and 3/8" diameter. It comes with a large round knob pressed onto a 1/4"-20 x 1" bolt. By attaching the arm using the knob you will not only extend the reach of the ball but will have the ability to swivel the arm side to side. It's black in color, made out of 6061 T6 aircraft-grade aluminum with Type III anodizing and the included hardware is 316 stainless steel.

Ultralight SBSS-8 YS style single ball arm. The SBSS-8 is a YS style single ball standard arm. It was made for Sea & Sea strobes and lights using the YS style mount. It has a 5/16" and 3/8" hole on one end, 1" ball on the other and measures 8" from O-ring to the 5/16" hole with a 9" total length. It's black in color and made out of 6061 T6 aircraft-grade aluminum with Type III anodizing.

Ultralight SBSS-8RB YS style single ball arm with large knob. The SBSS-8RB is like our standard DB-05 arm but with a single ball on one end a 1/2" thick flat surface on the other with two holes. It measures 8" from O-ring to the 5/16" hole with a 9" total length. The two holes are 5/16" and 3/8" diameter. It comes with a large round knob pressed onto a 1/4"-20 x 1" bolt. By attaching the arm using the knob you will not only extend the reach of the ball but will have the ability to swivel the arm side to side. It's black in color, made out of 6061 T6 aircraft-grade aluminum with Type III anodizing and the included hardware is 316 stainless steel.

Ultralight TR-CMB cinema all-purpose universal monitor bracket and accessory tray. The TR-CMB was designed so multiple 5” to 7” monitors and other accessories can be attached with a number of mounting options for camera assistants to create their video setups. With the endless mounting possibilities the tray provides it will work equally as well for anything filmmaking making it an excellent choice for DIT’s or broadcast. Due to how quick it can be adapted and the sturdiness of the tray, even grippers will find it extremely useful for quick and sturdy rigging. The tray is 18" long, 1 ¼” wide and 1/4" thick. It has three mounting locations for the ARRI 3/8” with locating pins, two 3 1/2” long by ¼” wide slots, six ¼” threaded holes, and two ¼” countersunk holes at each end to attach the TR-CMBH handle extensions. The tray is black in color and made out of 6061 T6 aircraft-grade aluminum with Type III anodizing. To make this a caged camera/monitor tray and the best possible version of itself order our CDTK-LDHMM and have the best of both worlds.

Ultralight TR-CMBH handle extension bracket for the TR-CMB accessory tray. The TR-CMBH handle bracket was designed to be added to the TR-CMB tray so the Ultralight AC-H1/4XL style handle could be added creating a complete combo setup that can be easily carried. The handle bracket is 4” long, 1 ¼” wide and ¼” thick, and has a 3/8” hole for attaching the handle to it. Adding to the versatility of the bracket it has one ¼” center pivot hole and one 1/4” curved slot making it swingable when mounted. It's black in color, made out of 6061 T6 aircraft-grade aluminum with Type III anodizing and the included hardware is 316 stainless steel.

Ultralight TR-D small single handle camera tray. The TR-D was designed as a single handle camera tray for small sized point and shoot housings. Made to use with camera housings with one 1/4" mounting hole. It comes with a 1/4"-20 captive bolt with thumb knob and 1/4" plastic washer and has a 4" long raised backstop which holds the housing in place when mounted. The tray is 8 1/2" long, 2" at the widest point, 1" at the narrowest and 1/4" thick. It has three 1 1/2" long 1/4" slot and one 3/8" hole, two 1/4" threaded holes and two holes on one end to mount an extension for a second handle . Made to use with camera housings with one 1/4" mounting hole. Any ULCS tray extension or handle will fit the TR-D. It's black in color, made out of 6061 T6 aircraft-grade aluminum with Type III anodizing and the included hardware is 316 stainless steel.